ALFUN a.s.

Aluminium sheets and strips

We offer aluminium sheets and strips in the thickness 0,3 – 5,0 mm and according to your requested dimensions. 

 

Terms and characteristics  

Term according ENMetallurgical termCSNDINCorrosion resistanceSuitable for anodising processWeldability
EN AW 1050 AL99,5 424005 3.0255 very good yes very
EN AW 3003 AlMn1Cu   3.0517 very good no very
EN AW 3103 AlMn1 424432 3.0515 very good no very
EN AW 3004 AlMn1Mg1   3.0526 very good no very
EN AW 3005 AlMn1Mg0,5   3.0525 very good no very
EN AW 3105 AlMn0,5Mg0,5   3.0505 very good no very
EN AW 5005 AlMg1   3.3315 especially against to sea water yes very
EN AW 5049 AlMg2Mn0,8   3.3527 especially against to sea water yes very
EN AW 5052 AlMg2,5   3.3523 especially against to sea water yes very
EN AW 5251 AlMg2Mn0,3 424412 3.3525 especially against to sea water yes very
EN AW 5754 AlMg3 424413 3.3535 especially against to sea water yes very
EN AW 5083 AlMg4,5Mn0,7 424415 3.3547 especially against to sea water no very
EN AW 6082 AlMgSi1Mn 424400 3.2315 especially against to sea water yes very
EN AW 7020 AlZn4,5Mg1 424441 3.4335 low no not suitable
EN AW 7022 AlZn5Mg3Cu   3.4345 low no not suitable
EN AW 7075 AlZn5,5MgCu 424222 3.4365 low no not suitable
EN AW 2017 AlCu4MgSi 424201 3.1325 low no low
EN AW 2024 ALCu4Mg1 424203 3.1355 low no low

Note:
1. This is only an approximate comparison according to chemical composition or mechanical values.
2. This must be specified in the order, if the material should undergo the anodising process.
3. Statement about suitable for anodising process in for information only.

 

Mechanical properties

AlloyTemperRm (Mpa)Rp 0,2
MPa
min.max.
Al99,5
EN AW 1050
0/H111 soft 65 95 20
H12/H22 1/4 hard 85 125 65
H14/H24 1/2 hard 105 145 85
H16/H26 3/4 hard 120 160 100
H18/H28 hard 140   120
AlMnCu
EN AW 3003
0/H111 soft 95 135 35
H14/H24 1/2 hard 145 185 125
H18/H28 hard 185   165
AlMn1 0/H111 soft 90 130 35
H14/H24 1/2 hard 140 180 120
H16/H26 3/4 hard 160 200 145
H18/H28 hard 185   165
AlMn1Mg1
EN AW 3004
0/H111 soft 155 200 60
H12/H22 1/4 hard 190 240 155
H14/H24 1/2 hard 220 265 180
H16/H26 3/4 hard 245 285 200
H18/H28 hard 260   230
AlMn1Mg0,5
EN AW 3005
0/H111 soft 115 165 45
H12/H22 1/4 hard 145 195 125
H14/H24 1/2 hard 170 215 150
H16/H26 3/4 hard 195 240 175
H18/H28 hard 220   200
AlMn0,5Mg0,5
EN AW 3105
0/H111 soft 100 155 40
H12/H22 1/4 hard 130 180 105
H14/H24 1/2 hard 150 200 130
H16/H26 3/4 hard 175 225 160
H18/H28 hard 195   180
AlMg1
EN AW 5005
0/H111 soft 100 145 35
H22/H32 1/4 hard 125 165 80
H24/H34 1/2 hard 145 185 110
AlMg2
EN AW 5251
0/H111 soft 160 200 60
H22/H32 1/4 hard 190 230 120
H24/H34 1/2 hard 210 250 140
AlMg2Mn0,8
EN AW 5049
0/H111 soft 190 240 80
H22/H32 1/4 hard 220 270 130
H24/H34 1/2 hard 240 280 160
H26/H36 3/4 hard 265 305 190
AlMg2,5
EN AW 5052
0/H111 soft 170 215 65
H22/H32 1/4 hard 210 260 130
H24/H34 1/2 hard 230 280 150
H26/H36 3/4 hard 250 300 180
AlMg3
EN AW 5754
0/H111 soft 190 240 80
H22/H32 1/4 hard 220 270 130
H24/H34 1/2 hard 240 280 160
H26/H36 3/4 hard 265 305 190
H114 tread plate 190 260 80
AlMg4,5Mn0,7
EN AW 5083
0/H111 soft 275 350 125
H22/H32 1/4 hard 305 380 215
H24/H34 1/2 hard 340 400 250
AlMg1SiCu
EN AW 6061
0 soft unspecify 150 max. 85
T4/T451 naturally aged 205 unspecify 110
T6/T651 artificially aged 290 unspecify 240
AlSiMgMn
EN AW 6082
0 soft unspecify 15 max. 85
T4/T451 naturally aged 205 unspecify 110
T6/T651 artificially aged 310 unspecify 260
AlCu4MgSi
EN AW 2017A
0 soft unspecify 225 145
T4/T451 naturally aged 390 unspecify 245
AlCu4Mg1
EN AW 2024
0 soft unspecify 220 140
T3/T351 naturally aged 420 unspecify 290
AlZn5Mg3Cu
EN AW 7022
T6/T651 artificially aged 450 unspecify 370
AlZn5,5MgCu
EN AW 7075
0 soft 275 unspecify 145
T651 artificially aged 525 unspecify 440

 

Table of elongation and informative bending radius for particular temper and the range of the material thicknesses.

Alloy EN AW-1050A [99,5]
TemperNominal thickness mmElongation min. %Bending radius 1)
overupA50 mm180°90°
0/H111 0.2 0.5 20 0 t 0 t
0.5 1.5 22 0 t 0 t
1.5 3.0 26 0 t 0 t
3.0 6.0 29 0.5 t 0.5 t
H12 0.2 0.5 2 0.5 t 0 t
0.5 1.5 4 0.5 t 0 t
1.5 3.0 5 0.5 t 0.5 t
3.0 6.0 7 1.0 t 1.0 t
H14 0.2 0.5 2 1.0 t 0 t
0.5 1.5 3 1.0 t 0.5 t
1.5 3.0 4 1.0 t 1.0 t
3.0 6.0 5   1.5 t
H16 0.2 0.5 1   0.5 t
0.5 1.5 2   1.0 t
1.5 4.0 3   1.5 t
         
H18 0.2 0.5 1   1.0 t
0.5 1.5 2   2.0 t
1.5 3.0 2   3.0 t
         
H22 0.2 0.5 4 0.5 t 0 t
0.5 1.5 5 0.5 t 0 t
1.5 3.0 6 0.5 t 0.5 t
3.0 6.0 7 1.0 t 1.0 t
H24 0.2 0.5 3 1.0 t 0 t
0.5 1.5 4 1.0 t 0.5 t
1.5 3.0 5 1.0 t 1.0 t
3.0 6.0 6 1.5 t 1.5 t
H26 0.2 0.5 2   0.5 t
0.5 1.5 3   1.0 t
1.5 3.0 4   1.5 t
         
H28 0.2 0.5 2   1.0 t
0.5 1.5 2   2.0 t
1.5 3.0 3   3.0 t
         

1) Only informatively, t=material thickness

 

Table of elongation and informative bending radius for particular temper and the range of the material thicknesses.

Alloy EN AW-5754 [AlMg3]
 Nominal thickness mmTažnost min. %Bending radius 1)
TemperoverupA50 mm180°90°
0/H111 0.2 0.5 12 0.5 t 0 t
0.5 1.5 14 0.5 t 0.5 t
1.5 3.0 16 1.01 t 1.01 t
3.0 6.0 18 1.01 t 1.01 t
H12 0.2 0.5 4    
0.5 1.5 5    
1.5 3.0 6    
3.0 6.0 7    
H14 0.2 0.5 3    
0.5 1.5 3    
1.5 3.0 4    
3.0 6.0 4    
H16 0.2 0.5 2    
0.5 1.5 3    
1.5 3.0 3    
3.0 6.0 3    
H18 0.2 0.5 1    
0.5 1.5 2    
1.5 3.0 2    
         
H22/32 0.2 0.5 7 1.5 t 0.5 t
0.5 1.5 8 1.5 t 1.0 t
1.5 3.0 10 2.0 t 1.5 t
3.0 6.0 11   1.5 t
H24/34 0.2 0.5 6 2.5 t 1.0 t
0.5 1.5 6 2.5 t 1.5 t
1.5 3.0 7 2.5 t 2.0 t
3.0 6.0 8   2.5 t
H26/36 0.2 0.5 4   1.5 t
0.5 1.5 4   2.0 t
1.5 3.0 5   3.0 t
3.0 6.0 6   3.5 t
H28/38 0.2 0.5 3    
0.5 1.5 3    
1.5 3.0 4    
         

1) Only informatively, t=material thickness

 

 



EMPTY

KOSIK
loading